Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Albany Homeowners
A gate that won’t open is a problem you feel every time you pull into the driveway. Maybe the arm on your operator jammed halfway through a cycle, or a hinge pin sheared off and the gate is hanging on one post. Whatever the failure, we handle it as gate specialists, not as a side job between other trades. Our technicians have up to 12 years of experience, they arrive knowing they’re looking at a gate, and they carry the diagnostic gear to trace both mechanical and electronic faults in a single visit. We specialize exclusively in gates, which means no guessing and fewer callbacks. Same-day service is often possible when you call early. Reach us at (866) 942-6084 for a free estimate.
Driveway Gate Repair
Driveway Gate Repair covers everything between your gate panels and the operator arm that moves them, and it’s the call we field most often when a gate stops mid-travel or sags on its posts. You need it when the gate drops, drags on the ground, binds against the strike post, or when the arm pushes but the gate doesn’t budge. We diagnose the mechanical side first, because a bent arm or a wallowed hinge will mimic an electrical fault. We fix the panel, the frame, the hinges, the chain or the operator linkage and get the whole assembly running true again. Most driveway gate repairs fall in the $150 to $650 range depending on what’s failed and whether parts need ordering. The written estimate sets the final price, and it’s agreed before any work starts.
Sagging and Dropping Gates
A gate that sags is usually a hinge, post, or footing issue rather than a panel problem. We check hinge wear, post plumb, and footing movement in order, so we fix the cause instead of just lifting the panel. Left alone, a sag will strain the operator and eventually burn out the motor.
Binding and Clearance Problems
Gates that bind against the strike post or scrape the driveway usually have shifted clearance, warped framing, or a hinge that’s gone sloppy. We measure the swing path and check ground clearance, then correct the alignment rather than forcing it. Getting clearance right protects both the panel and the operator.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Welding
Gate Welding is the structural side of gate work, and it’s what a gate needs when a hinge bracket cracks, a picket breaks loose, or a weld on the frame lets go after years of use. It applies to steel and iron gates especially, since those are the materials that fail at welds rather than sagging. We reweld cracked hinge brackets, rebuild broken frame joints, repair popped pickets, and reattach hardware that’s pulled out of the metal. Welding on a load-bearing gate panel isn’t something to attempt without the right equipment. Our technicians weld on site and check the repair under load before the gate goes back into service. A gate weld repair typically runs $150 to $450 depending on how many joints are affected and the access. The final price comes from the written estimate, agreed before we start.
Cracked Hinge and Bracket Welds
Hinge brackets take constant stress and are the first weld to fail on a steel gate. We grind out the old weld, reset the bracket, and reweld it with full penetration so it holds under operator load. A failed bracket that’s left alone will crack the frame next.
Structural Frame Repair
Frame welds crack at corners and at points where a gate meets its post bracket. We repair the joint, reinforce it where it makes sense, and check the frame is still square before reinstalling. Out-of-square frames are the usual cause of gates that never hang correctly.
Commercial Gate Repair
Commercial Gate Repair covers the heavier gates and access-control operators that businesses, apartment complexes, and property managers rely on for controlled entry. You need it when a slide or swing gate on a commercial operator fails, when loop detectors stop detecting, or when the gate won’t accept a credential from the access-control system. We diagnose the mechanical gate and the electronic operator together, because commercial failures often live in both. We service the leading access-control brands, including DoorKing and FAAC units, and we trace faults through the control board, safety sensors, and loop detectors rather than guessing. Commercial repair typically runs $200 to $850 depending on the operator and the fault, and the written estimate sets the final price. Every job is quoted and agreed before work begins.
Access-Control and Loop Detector Faults
Loop detectors are one of the most misdiagnosed parts on a commercial gate. When a gate won’t close, we test the loop, the detector card, and the safety edges in sequence so we replace only what’s failed. Drifting detectors and damaged loop wire are the usual culprits.
Heavy-Duty Operator Service
Commercial operators carry more cycles, more weight, and more heat than residential units. We check the control board, the motor windings, the limit settings, and the hydraulic or chain drive depending on the model. Getting the operator serviced correctly is what keeps entry lanes from backing up.
Iron Gate Repair
Iron Gate Repair handles the failures specific to iron and iron-alloy gates, where the metal is strong but the joints and hardware are usually what give out first. You need it when an iron gate drops, a hinge pulls free, or the gate won’t latch squarely in the strike. We rehang iron gates on their posts, repair or replace worn hinges, correct sag, and reweld failed joints. Iron is unforgiving when a fix is done wrong, so we check plumb and swing before we close out the job. Iron gate repair usually lands between $180 and $600 depending on the number of hinges, welds, and hardware involved. The price is quoted from the written estimate and agreed before work starts, with a free estimate up front.
Hinge and Post Repairs
Iron hinges wear at the pin and pull loose at the post bracket over time. We replace worn hinge hardware and reset post brackets so the gate swings clean, without the play that puts strain on the operator. Worn hinges are also the leading cause of operator failure on heavy gates.
Rust and Joint Repairs
Iron joints are where rust starts, and rusting joints weaken the whole frame. We clean out failing welds, repair the joint, and treat the steel at the repair point. A joint that’s rusting through won’t hold a weld until it’s cleaned and rebuilt.
Sliding Gate Repair
Sliding Gate Repair deals with gates that travel horizontally instead of swinging, and it covers track faults, wheel failures, and off-track panels. You need it when the gate jumps the track, rolls rough, stops short, or the roller wheels wear down to metal. We replace worn rollers, realign bent or damaged track, rehang panels that have come off the track, and check the operator stops and limits so the gate travels cleanly. A slide gate that’s come off its track can drop and injure someone, so it should be a stop-and-fix item, not a wait-and-see one. Sliding gate repair typically costs $180 to $700 depending on the track, rollers, and operator settings involved. The written estimate sets the price, and it’s agreed before we begin.
Track and Roller Wear
Rollers wear fastest on slide gates that see constant use, and worn rollers drag the panel, which bends the track. We inspect rollers, replace the worn set, and check track straightness before reassembly. New rollers on a bent track will wear just as fast.
Off-Track and Alignment Repair
A slide gate that’s jumped its track needs rehanging, and the alignment has to be corrected before it goes back into service. We rehang the panel, check the guide rollers, and reset the operator limits. Off-track gates are a safety issue and a sure path to operator damage if pushed back into use.
Wrought Iron Gate Repair
Wrought Iron Gate Repair covers the ornamental iron gates on many Albany properties, where the decorative detail is as important as the structure. You need it when a wrought iron gate sags, a picket is bent, a decorative scroll is loose, or the gate won’t latch where the strike meets the frame. We repair the structural joints, straighten bent ornamental work where the metal allows, and rehang the gate so it lines up properly. Ornamental gates take careful welding since the decorative details are thinner than structural steel. Wrought iron gate repair usually runs $200 to $650 depending on the ornamentation and structural work involved. The written estimate is free and sets the final price, agreed before any work starts.
Ornamental Detail Repair
Scrollwork and decorative pickets can bend or break away at the weld. We repair the detail with careful heat control so the ornament doesn’t distort, then check the joint. Ornamental work needs patience and the right welding settings.
Latch and Strike Alignment
A wrought iron gate that won’t latch squarely usually has a sag or a strike that’s moved. We correct the sag, reset the strike and latch, and confirm the gate closes cleanly. A misaligned latch will wear the strike until it fails completely.
Metal Gate Repair
Metal Gate Repair is the general category for steel, aluminum, and other metal gates that need mechanical or structural work rather than ornamental detail. You need it when a steel gate drops, a hinge pulls, a weld cracks, or the gate binds and drags in the swing. We fix the frame, hinges, posts, and hardware, then confirm alignment so the operator isn’t fighting a bent gate. Metal gates are strong panels on relatively small hardware, so most failures trace back to the hinge line or the post bracket. Metal gate repair typically costs $150 to $550 depending on the fault and the gate’s construction. The written estimate sets the price, agreed before work begins, and the estimate is free.
Steel and Aluminum Hinge Repairs
Steel and aluminum gates hang on hinges that are far smaller than the panel they carry. We replace worn or failed hinges, reinforce the post bracket where weld fatigue is common, and rehang the gate square. Bad hinges are the single biggest contributor to gate sag.
Frame Straightening and Bracing
Frames bend when a gate drops or takes an impact. We straighten the frame where the metal allows, add bracing to the weak point where it makes sense, and confirm the gate swings true. A frame that stays bent is a gate that won’t latch and an operator that fails early.
Wood Gate Repair
Wood Gate Repair covers the timber gates that many Albany properties use for privacy and driveway control, and it addresses age, moisture, and hardware failures that wood gates tend to see. You need it when boards are warped, the gate sags, hinges have torn out of the wood, or the frame has gone out of square. We replace failed boards, repair or replace torn-out hinges, rehang the frame square, and reset the latch so the gate closes correctly. Wood moves with the seasons, so we check the frame against typical seasonal movement before we correct it. Wood gate repair typically runs $150 to $500 depending on the amount of board replacement and hinge work. The written estimate sets the final price and is agreed before work starts.
Hinge and Post Reinforcement
Wood hinges tear out at the screw points when the wood softens or the gate sags. We reinforce the hinge area, reset the hinges, and repair the post where the bracket has pulled. Screws that keep backing out are a sign the wood behind them has failed.
Board and Frame Repair
Warped or split boards weaken the gate and let the frame go out of square. We replace failed boards with matching stock and check the frame is square before rehanging. A frame that stays out of square never closes cleanly.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We service LiftMaster operators and know where those units tend to wear out – the arms, the limit settings, and the control boards. We also work on Mighty Mule gate operators, which are popular on residential swing and slide gates, and we know the sensor and gear issues those units see. On the commercial side, we service FAAC operators and their control boards, safety sensors, and loop detectors. We also work on BFT equipment across residential and light commercial setups, and we’re familiar with how those boards report faults.
Beyond those, we work on Linear, Viking, Ghost Controls, DoorKing, and Elite operators. We aren’t a dealer for any of them and we don’t push brand switches – we fix the equipment you already have rather than selling you a replacement you don’t need. Whether you have a LiftMaster, a Mighty Mule, or any other make, we can help.
Signs You Need a Pro Right Now
- The gate won’t close or won’t latch. A gate that stops short or won’t latch leaves the property open and puts strain on the operator arm every cycle. It usually points to an alignment, hinge, or operator limit fault that gets worse with use.
- The gate sags or drags. A sagging gate is a hinge or post failure waiting to become an operator failure. The drag adds resistance the motor was never designed to push, and motors fail under that load.
- The operator runs but the gate doesn’t move. When the motor cycles but the gate stays put, something in the linkage, chain, or drive has failed. Continuing to cycle it will damage the motor or the control board.
- You see a bent track or a gate off its track. A slide gate that’s jumped its track can drop, and pushing it back into service without resetting alignment leads to repeated failures. Stop using it until it’s checked.
- Safety sensors or loop detectors aren’t working. A safety device that fails to detect is a serious risk on any automated gate. Have the sensor or loop checked before the gate is put back into automatic operation.
Our Process, Step by Step
- 1
Call and describe the fault. Tell us the gate type, the brand if you know it, and what it’s doing. That first detail lets us show up with the right diagnostic gear and often the right parts. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
- 2
On-site diagnosis. We check the mechanical side first – hinges, posts, frame, track, and rollers – then test the operator controls, safety sensors, and limits. Diagnosing both sides in one visit is what keeps the fix accurate.
- 3
Free written estimate. We tell you what’s failed, what it takes to fix it, and what it costs, with the price in writing before work starts. No surprises on the invoice.
- 4
Repair and testing. We complete the repair, then run the gate through multiple full cycles, test the safety devices, and confirm the gate latches or stops where it should.
- 5
Walk-through. We show you what was fixed, what to watch for going forward, and how to spot early signs of the same fault coming back. Simple, practical, no upselling.
How Much Does Gate Repair Cost in Albany?
Gate repair in Albany generally runs from $150 to $850 depending on the type of failure and the gate. A typical driveway gate repair runs $150 to $650 depending on the fault and the parts needed. Sliding gate repair runs $180 to $700, iron gate repair $180 to $600, metal gate repair $150 to $550, wood gate repair $150 to $500, and wrought iron gate repair $200 to $650. A gate weld repair runs $150 to $450. Commercial gate repair runs $200 to $850 depending on the operator and the fault.
Several things move the price. The gate type and material set the labor involved. The operator brand and age decide whether parts are available locally or need ordering. Whether the fault is purely mechanical, purely electronic, or both affects diagnostic time. Access to the gate, and whether a heavy gate needs a second technician, also affects cost. We don’t bill by the hour; the price is set per job by the written estimate.
To avoid overpaying, get a written estimate that lists what’s being repaired and what the finished price is. Ask whether the price includes testing the operator and safety devices afterward, not just the repair. A cheap fix that leaves the operator or safety devices untested is a repair you’ll redo. Our estimate is free and covers all of that. Call (866) 942-6084 for an exact quote – estimates are free.
Our Service Area Near Albany
We repair gates across Albany and the surrounding Capital Region, including gate repair in Roessleville, gate repair in Loudonville, and work throughout Rensselaer, Menands, Westmere, Colonie, Hampton Manor, Latham, Watervliet, East Greenbush, and Voorheesville. Same-day service is often possible when you call early. For our full lineup of gate services, see Gate Repair Albany, and for related work see our pages on gate repair, electric gate repair, and gate installation.
Serving Albany, NY – Our Local Coverage Area
We serve Albany and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Albany
Gate Repair is the diagnosis and correction of failures across a gate system: the panels, frame, hinges, posts, track, rollers, and the operator or motor when the gate is automated. It covers both mechanical faults (sag, cracked welds, jump off the track) and electronic faults (control board, safety sensors, loop detectors). A good gate repair fixes the actual cause, not just the symptom, and confirms the whole system works together afterward.
Most gate repairs are completed in a single visit, typically one to three hours depending on the fault and the gate type. Simple fixes like a hinge replacement or a latch alignment are usually done inside an hour. Operator faults and slide gate track issues can take longer, especially if a part needs ordering. We’ll give you a realistic time estimate with the written quote.
Gate repair in Albany typically runs $150 to $850 depending on the gate type and what’s failed. Driveway gate repair tends to run $150 to $650, sliding and wrought iron repairs $180 to $700, and commercial gate repair $200 to $850. The written estimate sets the final price and is agreed before we start. Call (866) 942-6084 for an exact quote – estimates are free.
Yes. We service LiftMaster and Mighty Mule operators along with FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, and Elite. We aren’t a dealer for any of them and don’t push replacements if a repair will fix the problem. We fix the equipment you already have.
Same-day service is often possible when you call early, and we answer 24/7. Fast dispatch runs 7am to 7pm, Sunday through Friday, and we’re closed Saturday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
We stand behind the work we do, and our written estimate spells out what’s covered. Parts carry their manufacturers’ warranties, and we walk you through what applies to the repair before we finish. If something related to the repair isn’t right afterward, call us and we’ll make it right.
Clear access to the gate on both sides, and if possible note the operator brand, the model, and what the gate does when it fails. If the gate is automated, don’t force it open or closed by hand more than needed – that can damage the operator. Have anyone who uses the gate or any access codes ready to walk the technician through the fault.
Schedule Your Gate Repair Service in Albany Today
When your gate won’t open, won’t close, or isn’t acting right, don’t wait for the fault to turn into a bigger repair. Call (866) 942-6084. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. We’ll give you a free, no-obligation estimate, agree the price before any work starts, and get your gate working the way it should.
Written by the team at Gate Repair Albany.